';
view
Our ballasts are available in various models with different output power, ranging from 3,0 kW to 68,9 kW.
Thanks to this wide range of output power our ballast provide the highest quality and value and they can be used in demanding applications. There are two different ballasts power configurations:
HPE long-standing expertise and its know-how, honed over the years, has led to the design and manufacturing of the new SERIES R. For all SERIES R ballasts the cooling section has been dramatically redesigned and it now has an air flow channelling system equipped with ducts that conveys the cooling airflow to the hot areas only and in a targeted manner. Thanks to this ducting system it was possible to create some completely sealed and insulated areas where electronic components can be placed, so that these are protected from any external conditions and factors in the surrounding working area that may jeopardize their life cycle. The fan unit is positioned at the rear of the machine and it consists of a set of 24 Vdc fans powered by an internal source. The airflow passes through the ballast along its longitudinal axis and the direction of the airflow can be chosen between the following versions available when ordering the equipment: Version F, t.i. FORWARD, with the fans pushing air into the machine, and Version B, t.i. BACKWARD, with the fans pulling air out of the machine.
Electrical layouts available:
For all configurations the connection to any automation systems, compatibly with the SERIES H, is possible by means of two RJ45 connectors for ModBus-RTU connection, and two connectors for “Can HPE” net.
In line with HPE company policy, the supply voltage of the main circuit and the supply voltage of the auxiliary circuits are kept separate, as the supply voltage of the auxiliary circuits must never be turned off (disconnected) to ensure that the protection circuits are always active.
Here below you can find the description of the available electrical layouts:
/ Rx0x /
Configurazione standard, applicabile a macchine che lavorano con tensione di rete fino a 480 Vac totalmente compatibile con la SERIE H. Necessita di una sorgente 24 Vdc – 1,0 A protetta non sezionabile che serve per alimentare i circuiti ausiliari e di sicurezza. La sorgente per alimentare i ventilatori, a differenza della SERIE H, viene prelevata internamente dall’alimentazione primaria di rete 220 Vac – 480 Vac e regolata a 24 Vdc da un alimentatore interno. Quindi i ventilatori entreranno in funzione quando la tensione di principale di alimentazione (220 Vac – 480 Vac) sarà connessa.
Nota: per i ballast R200 e R400 la sorgente ausiliaria dovrà essere di 2,5 A.
/ Rx1x /
Opzione valida per tutti i modelli della SERIE R ad esclusione del R200. In questa configurazione la sorgente a 24 Vdc non è necessaria in quanto l’alimentazione dei circuiti ausiliari e dei ventilatori avviene tramite la tensione di rete in un range che va da 220 Vac a 480 Vac. Sul frontale della macchina è presente un connettore che dovrà essere connesso alla rete in modo protetto ma non sezionabile. Un power supply interno alla macchina provvederà a generare le tensioni necessarie a tutte le funzioni ausiliarie.
/ Rx2x /
Configurazione, compatibile con la SERIE H e preferibilmente applicabile a macchine che lavorano con tensioni di rete maggiore a 480 Vac, tipicamente 600 Vac. Necessita di una sorgente 24 Vdc – 1,0 A protetta non sezionabile che serve per alimentare i circuiti ausiliari e di sicurezza. L’attivazione dei ventilatori avverrà a mezzo di una tensione AC monofase da 300 Vac a 480 Vac collegata ad un connettore posto sul frontale della macchina. In questa configurazione l’attivazione dei ventilatori potrà essere comandata indipendentemente dalla tensione di alimentazione della macchina.
All the R SERIES ballasts, with the same power and size, are compatible with the previous H SERIES, also in terms of dimensions and overall dimensions.
Our ballasts are also available in the COMBO version: these ballast are specifically designed for the switching on of traditional UV lamps as well as of our UV LEDs.
HPE TECHNOLOGY
The on-board software, fully developed by HPE, continuously monitors all the functions of the LED and it also provides comprehensive diagnostic functions with regard to the LED or to the lamp connected.
The alarm system immediately sends an alarm message in case of faults or malfunctions.
PRODUCT CATALOGUE
Unlike the most common converters/power supply units available on the market that simply regulate current and voltage, HPE systems allow to:
Monitor all the physical parameters of the lamps (voltage, overvoltage, temperature, ageing and faults)
Manage the whole drying system, by monitoring the housing group and the cooling process of the lamp
Analyse the efficiency of the system and send alarm messages to ensure correct functioning of the UV unit
Operate in a specific and univocal way, if they are integrated as slave in a hierarchically superior system
